Select between two sources with transistors
I'm sorry if this has been asked before but I can't find useful data on this matter.
I have two sources of data and I want to select one of them using transistors.
If I had to guess I'd make the circuit below.
Sadly I never had any electronics courses so maybe I'm missing something obvious here but as I can't find anything about my goal on internet I'd rather ask here.
I just heard about SSRs and they seem to be the best solution for my needs, but I still want to know about how to do this with transistors if this is possible.
Thanks
Vout is bottom-right
Edit:
The sources are composite video signals
transistors relay voltage-source
asked yesterday
RenéX
83
New contributor
RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I'm sorry if this has been asked before but I can't find useful data on this matter.
I have two sources of data and I want to select one of them using transistors.
If I had to guess I'd make the circuit below.
Sadly I never had any electronics courses so maybe I'm missing something obvious here but as I can't find anything about my goal on internet I'd rather ask here.
I just heard about SSRs and they seem to be the best solution for my needs, but I still want to know about how to do this with transistors if this is possible.
Thanks
Vout is bottom-right
Edit:
The sources are composite video signals
transistors relay voltage-source
asked yesterday
RenéX
83
New contributor
RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
What kind of “sources” are these?
– user2233709
yesterday
They are composite video signals
– RenéX
22 hours ago
add a comment |
I'm sorry if this has been asked before but I can't find useful data on this matter.
I have two sources of data and I want to select one of them using transistors.
If I had to guess I'd make the circuit below.
Sadly I never had any electronics courses so maybe I'm missing something obvious here but as I can't find anything about my goal on internet I'd rather ask here.
I just heard about SSRs and they seem to be the best solution for my needs, but I still want to know about how to do this with transistors if this is possible.
Thanks
Vout is bottom-right
Edit:
The sources are composite video signals
transistors relay voltage-source
asked yesterday
RenéX
83
New contributor
RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I'm sorry if this has been asked before but I can't find useful data on this matter.
I have two sources of data and I want to select one of them using transistors.
If I had to guess I'd make the circuit below.
Sadly I never had any electronics courses so maybe I'm missing something obvious here but as I can't find anything about my goal on internet I'd rather ask here.
I just heard about SSRs and they seem to be the best solution for my needs, but I still want to know about how to do this with transistors if this is possible.
Thanks
Vout is bottom-right
Edit:
The sources are composite video signals
transistors relay voltage-source
transistors relay voltage-source
asked yesterday
RenéX
83
New contributor
RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked yesterday
RenéX
83
New contributor
RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 22 hours ago
asked yesterday
RenéX
83
New contributor
RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked yesterday
RenéX
83
asked yesterday
RenéX
83
83
New contributor
RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
What kind of “sources” are these?
– user2233709
yesterday
They are composite video signals
– RenéX
22 hours ago
add a comment |
What kind of “sources” are these?
– user2233709
yesterday
They are composite video signals
– RenéX
22 hours ago
What kind of “sources” are these?
– user2233709
yesterday
What kind of “sources” are these?
– user2233709
yesterday
They are composite video signals
– RenéX
22 hours ago
They are composite video signals
– RenéX
22 hours ago
add a comment |
2 Answers
2
active
oldest
votes
If you're selecting between two sources of binary digital data, you should be looking for a digital multiplexer. If you're selecting between two analog signals you should be looking for an analog multiplexer. There are dozens of part numbers of either type available from the major IC vendors, depending on the details of your requirements.
Buying either of these circuits as an IC will probably be lower cost (after accounting for assembly costs) and almost certainly be more reliable and give more consistent results than constructing them out of transistors.
answered yesterday
The Photon
83.4k396194
Thanks I'll look at these analog multiplexers.
– RenéX
22 hours ago
By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
– RenéX
22 hours ago
To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
– The Photon
20 hours ago
I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
– RenéX
4 hours ago
add a comment |
Part like this will do for analog or digital switching at 3.3V levels.
https://www.analog.com/media/en/technical-documentation/data-sheets/ADG839.pdf
What voltage and current levels are you after?
answered yesterday
CrossRoads
1,2028
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
});
});
}, "mathjax-editing");
StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "135"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
RenéX is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f415470%2fselect-between-two-sources-with-transistors%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
If you're selecting between two sources of binary digital data, you should be looking for a digital multiplexer. If you're selecting between two analog signals you should be looking for an analog multiplexer. There are dozens of part numbers of either type available from the major IC vendors, depending on the details of your requirements.
Buying either of these circuits as an IC will probably be lower cost (after accounting for assembly costs) and almost certainly be more reliable and give more consistent results than constructing them out of transistors.
answered yesterday
The Photon
83.4k396194
Thanks I'll look at these analog multiplexers.
– RenéX
22 hours ago
By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
– RenéX
22 hours ago
To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
– The Photon
20 hours ago
I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
– RenéX
4 hours ago
add a comment |
If you're selecting between two sources of binary digital data, you should be looking for a digital multiplexer. If you're selecting between two analog signals you should be looking for an analog multiplexer. There are dozens of part numbers of either type available from the major IC vendors, depending on the details of your requirements.
Buying either of these circuits as an IC will probably be lower cost (after accounting for assembly costs) and almost certainly be more reliable and give more consistent results than constructing them out of transistors.
answered yesterday
The Photon
83.4k396194
Thanks I'll look at these analog multiplexers.
– RenéX
22 hours ago
By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
– RenéX
22 hours ago
To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
– The Photon
20 hours ago
I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
– RenéX
4 hours ago
add a comment |
If you're selecting between two sources of binary digital data, you should be looking for a digital multiplexer. If you're selecting between two analog signals you should be looking for an analog multiplexer. There are dozens of part numbers of either type available from the major IC vendors, depending on the details of your requirements.
Buying either of these circuits as an IC will probably be lower cost (after accounting for assembly costs) and almost certainly be more reliable and give more consistent results than constructing them out of transistors.
answered yesterday
The Photon
83.4k396194
If you're selecting between two sources of binary digital data, you should be looking for a digital multiplexer. If you're selecting between two analog signals you should be looking for an analog multiplexer. There are dozens of part numbers of either type available from the major IC vendors, depending on the details of your requirements.
Buying either of these circuits as an IC will probably be lower cost (after accounting for assembly costs) and almost certainly be more reliable and give more consistent results than constructing them out of transistors.
answered yesterday
The Photon
83.4k396194
answered yesterday
The Photon
83.4k396194
answered yesterday
The Photon
83.4k396194
answered yesterday
The Photon
83.4k396194
83.4k396194
Thanks I'll look at these analog multiplexers.
– RenéX
22 hours ago
By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
– RenéX
22 hours ago
To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
– The Photon
20 hours ago
I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
– RenéX
4 hours ago
add a comment |
Thanks I'll look at these analog multiplexers.
– RenéX
22 hours ago
By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
– RenéX
22 hours ago
To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
– The Photon
20 hours ago
I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
– RenéX
4 hours ago
Thanks I'll look at these analog multiplexers.
– RenéX
22 hours ago
Thanks I'll look at these analog multiplexers.
– RenéX
22 hours ago
By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
– RenéX
22 hours ago
By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
– RenéX
22 hours ago
To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
– The Photon
20 hours ago
To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
– The Photon
20 hours ago
I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
– RenéX
4 hours ago
I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
– RenéX
4 hours ago
add a comment |
Part like this will do for analog or digital switching at 3.3V levels.
https://www.analog.com/media/en/technical-documentation/data-sheets/ADG839.pdf
What voltage and current levels are you after?
answered yesterday
CrossRoads
1,2028
add a comment |
Part like this will do for analog or digital switching at 3.3V levels.
https://www.analog.com/media/en/technical-documentation/data-sheets/ADG839.pdf
What voltage and current levels are you after?
answered yesterday
CrossRoads
1,2028
add a comment |
Part like this will do for analog or digital switching at 3.3V levels.
https://www.analog.com/media/en/technical-documentation/data-sheets/ADG839.pdf
What voltage and current levels are you after?
answered yesterday
CrossRoads
1,2028
Part like this will do for analog or digital switching at 3.3V levels.
https://www.analog.com/media/en/technical-documentation/data-sheets/ADG839.pdf
What voltage and current levels are you after?
answered yesterday
CrossRoads
1,2028
answered yesterday
CrossRoads
1,2028
answered yesterday
CrossRoads
1,2028
answered yesterday
CrossRoads
1,2028
1,2028
add a comment |
add a comment |
RenéX is a new contributor. Be nice, and check out our Code of Conduct.
RenéX is a new contributor. Be nice, and check out our Code of Conduct.
RenéX is a new contributor. Be nice, and check out our Code of Conduct.
RenéX is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f415470%2fselect-between-two-sources-with-transistors%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
What kind of “sources” are these?
– user2233709
yesterday
They are composite video signals
– RenéX
22 hours ago