How can I loosen a hard-to-reach square nut whose holder is broken?












5














I've been attempting to disassemble a generator at work to replace the starter cord. Being a suitcase-type generator, it's proved to be excessively painstaking. However, it's almost apart - I just have one bolt holding the remaining cover onto the generator. Unfortunately, I can't get the bolt undone.



The bolt is a fairly standard hex bolt, with the head on the outside of the generator. I can get a socket over the bolt just fine. My problem lies inside the generator with the nut, which is a square nut that's supposed to sit in a plastic holder to stop it from turning when you try to loosen the bolt. Annoyingly, the plastic holder is broken, so when I try to get the bolt out, it just results in the bolt and nut turning endlessly in the holder.



Being as the nut and holder are inside the generator, they're fairly difficult to get at - I've removed the side panel, so I have some access, but it's fairly limited. There's enough space to get a screwdriver in onto the top of the nut, but not much more - certainly not enough to get a socket or spanner or pliers onto the nut.



I should also note that this bolt will require significant torque to get started - it's been tightened by a power tool of some sort (no idea what); our rather limited selection of power tools don't have enough torque to do the job. It is possible to do by hand, with some effort - I've got the other bolts off - but this does mean that whether I'm trying to turn the bolt or keep the nut in place, it takes a lot of force.



A liberal application of WD40 hasn't helped; nor has any other combination of tools I've managed to come up with. What else can I do to get this bolt off?










share|improve this question









New contributor




ArtOfCode is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
















  • 1




    The generator in question is a Stanley SIG 2000 Silent, just in case anyone has had similar experiences in the past.
    – ArtOfCode
    yesterday










  • Hi and welcome. You can edit the question with this additional info. Look for the "edit' link under the post. Also, pictures light help.
    – mike65535
    yesterday










  • Apply penetrating oil like Liquid Wrench / Liquid Spanner, every day for a week. Then try again. WD40 and CRC556 are poor substitutes for the right fluid.
    – Criggie
    yesterday










  • I didn't get any pictures, @mike, which is why I didn't add any - but I'm going in again tomorrow and I'll try to get some then.
    – ArtOfCode
    17 hours ago
















5














I've been attempting to disassemble a generator at work to replace the starter cord. Being a suitcase-type generator, it's proved to be excessively painstaking. However, it's almost apart - I just have one bolt holding the remaining cover onto the generator. Unfortunately, I can't get the bolt undone.



The bolt is a fairly standard hex bolt, with the head on the outside of the generator. I can get a socket over the bolt just fine. My problem lies inside the generator with the nut, which is a square nut that's supposed to sit in a plastic holder to stop it from turning when you try to loosen the bolt. Annoyingly, the plastic holder is broken, so when I try to get the bolt out, it just results in the bolt and nut turning endlessly in the holder.



Being as the nut and holder are inside the generator, they're fairly difficult to get at - I've removed the side panel, so I have some access, but it's fairly limited. There's enough space to get a screwdriver in onto the top of the nut, but not much more - certainly not enough to get a socket or spanner or pliers onto the nut.



I should also note that this bolt will require significant torque to get started - it's been tightened by a power tool of some sort (no idea what); our rather limited selection of power tools don't have enough torque to do the job. It is possible to do by hand, with some effort - I've got the other bolts off - but this does mean that whether I'm trying to turn the bolt or keep the nut in place, it takes a lot of force.



A liberal application of WD40 hasn't helped; nor has any other combination of tools I've managed to come up with. What else can I do to get this bolt off?










share|improve this question









New contributor




ArtOfCode is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
















  • 1




    The generator in question is a Stanley SIG 2000 Silent, just in case anyone has had similar experiences in the past.
    – ArtOfCode
    yesterday










  • Hi and welcome. You can edit the question with this additional info. Look for the "edit' link under the post. Also, pictures light help.
    – mike65535
    yesterday










  • Apply penetrating oil like Liquid Wrench / Liquid Spanner, every day for a week. Then try again. WD40 and CRC556 are poor substitutes for the right fluid.
    – Criggie
    yesterday










  • I didn't get any pictures, @mike, which is why I didn't add any - but I'm going in again tomorrow and I'll try to get some then.
    – ArtOfCode
    17 hours ago














5












5








5







I've been attempting to disassemble a generator at work to replace the starter cord. Being a suitcase-type generator, it's proved to be excessively painstaking. However, it's almost apart - I just have one bolt holding the remaining cover onto the generator. Unfortunately, I can't get the bolt undone.



The bolt is a fairly standard hex bolt, with the head on the outside of the generator. I can get a socket over the bolt just fine. My problem lies inside the generator with the nut, which is a square nut that's supposed to sit in a plastic holder to stop it from turning when you try to loosen the bolt. Annoyingly, the plastic holder is broken, so when I try to get the bolt out, it just results in the bolt and nut turning endlessly in the holder.



Being as the nut and holder are inside the generator, they're fairly difficult to get at - I've removed the side panel, so I have some access, but it's fairly limited. There's enough space to get a screwdriver in onto the top of the nut, but not much more - certainly not enough to get a socket or spanner or pliers onto the nut.



I should also note that this bolt will require significant torque to get started - it's been tightened by a power tool of some sort (no idea what); our rather limited selection of power tools don't have enough torque to do the job. It is possible to do by hand, with some effort - I've got the other bolts off - but this does mean that whether I'm trying to turn the bolt or keep the nut in place, it takes a lot of force.



A liberal application of WD40 hasn't helped; nor has any other combination of tools I've managed to come up with. What else can I do to get this bolt off?










share|improve this question









New contributor




ArtOfCode is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











I've been attempting to disassemble a generator at work to replace the starter cord. Being a suitcase-type generator, it's proved to be excessively painstaking. However, it's almost apart - I just have one bolt holding the remaining cover onto the generator. Unfortunately, I can't get the bolt undone.



The bolt is a fairly standard hex bolt, with the head on the outside of the generator. I can get a socket over the bolt just fine. My problem lies inside the generator with the nut, which is a square nut that's supposed to sit in a plastic holder to stop it from turning when you try to loosen the bolt. Annoyingly, the plastic holder is broken, so when I try to get the bolt out, it just results in the bolt and nut turning endlessly in the holder.



Being as the nut and holder are inside the generator, they're fairly difficult to get at - I've removed the side panel, so I have some access, but it's fairly limited. There's enough space to get a screwdriver in onto the top of the nut, but not much more - certainly not enough to get a socket or spanner or pliers onto the nut.



I should also note that this bolt will require significant torque to get started - it's been tightened by a power tool of some sort (no idea what); our rather limited selection of power tools don't have enough torque to do the job. It is possible to do by hand, with some effort - I've got the other bolts off - but this does mean that whether I'm trying to turn the bolt or keep the nut in place, it takes a lot of force.



A liberal application of WD40 hasn't helped; nor has any other combination of tools I've managed to come up with. What else can I do to get this bolt off?







tools generator






share|improve this question









New contributor




ArtOfCode is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











share|improve this question









New contributor




ArtOfCode is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









share|improve this question




share|improve this question








edited yesterday





















New contributor




ArtOfCode is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









asked yesterday









ArtOfCode

1285




1285




New contributor




ArtOfCode is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.





New contributor





ArtOfCode is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.






ArtOfCode is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.








  • 1




    The generator in question is a Stanley SIG 2000 Silent, just in case anyone has had similar experiences in the past.
    – ArtOfCode
    yesterday










  • Hi and welcome. You can edit the question with this additional info. Look for the "edit' link under the post. Also, pictures light help.
    – mike65535
    yesterday










  • Apply penetrating oil like Liquid Wrench / Liquid Spanner, every day for a week. Then try again. WD40 and CRC556 are poor substitutes for the right fluid.
    – Criggie
    yesterday










  • I didn't get any pictures, @mike, which is why I didn't add any - but I'm going in again tomorrow and I'll try to get some then.
    – ArtOfCode
    17 hours ago














  • 1




    The generator in question is a Stanley SIG 2000 Silent, just in case anyone has had similar experiences in the past.
    – ArtOfCode
    yesterday










  • Hi and welcome. You can edit the question with this additional info. Look for the "edit' link under the post. Also, pictures light help.
    – mike65535
    yesterday










  • Apply penetrating oil like Liquid Wrench / Liquid Spanner, every day for a week. Then try again. WD40 and CRC556 are poor substitutes for the right fluid.
    – Criggie
    yesterday










  • I didn't get any pictures, @mike, which is why I didn't add any - but I'm going in again tomorrow and I'll try to get some then.
    – ArtOfCode
    17 hours ago








1




1




The generator in question is a Stanley SIG 2000 Silent, just in case anyone has had similar experiences in the past.
– ArtOfCode
yesterday




The generator in question is a Stanley SIG 2000 Silent, just in case anyone has had similar experiences in the past.
– ArtOfCode
yesterday












Hi and welcome. You can edit the question with this additional info. Look for the "edit' link under the post. Also, pictures light help.
– mike65535
yesterday




Hi and welcome. You can edit the question with this additional info. Look for the "edit' link under the post. Also, pictures light help.
– mike65535
yesterday












Apply penetrating oil like Liquid Wrench / Liquid Spanner, every day for a week. Then try again. WD40 and CRC556 are poor substitutes for the right fluid.
– Criggie
yesterday




Apply penetrating oil like Liquid Wrench / Liquid Spanner, every day for a week. Then try again. WD40 and CRC556 are poor substitutes for the right fluid.
– Criggie
yesterday












I didn't get any pictures, @mike, which is why I didn't add any - but I'm going in again tomorrow and I'll try to get some then.
– ArtOfCode
17 hours ago




I didn't get any pictures, @mike, which is why I didn't add any - but I'm going in again tomorrow and I'll try to get some then.
– ArtOfCode
17 hours ago










3 Answers
3






active

oldest

votes


















3














Sounds like a nice project for a couple hours that grows into a multi-weekend odyssey!



OPTION 1 I'd wedge a couple of thin paint scrapers under the exposed bolt head outside the shell of the unit, and take the bolt's head off with an angle grinder and a thin cut-off wheel



BUT CONSIDER spark danger - given this is a generator there was probably petrol or diesel in the area. You'll want to vent it absolutely to remove all trace of gas fumes. And do this outside, with an extinguisher and sand handy.



Once the bolt head is off, the bolt should drop into the housing and you can fish it out when the covers are removed.



Assembly, well that's not the reverse. You'll want to find some way to bolt it together without risking the same again. A dirty hack is to put a new longer bolt in from the inside-to-outside. The nut will be on the outside and a bit of thread should be exposed. You can file two spanner-flats into the thread before or after assembly. Or you could hacksaw a flat slot across the end for a screwdriver.



Also consider what other bolts on the unit might do the same in the future, and either reinforce their mounts with epoxy or fibreglass, or preemptively do a similar bolt hack.





Option 2 - Cut the casing around the bolt head, and deal with it once the cover is off. You'll probably want to do a patch job on the case after-ward to control fumes etc.





Option 3 - Make a tool to suit. This is probably the most laborious solution, but you know exactly where the nut is and how long your tool would have to be.



From http://www.performanceforums.com/forums/showthread.php?67243773-dodgy-homemade-distributor-spanner From http://www.performanceforums.com/forums/showthread.php?67243773-dodgy-homemade-distributor-spanner



Given how cheap tools are these days, there's no shame in sacrificing a cheap combo ring/open spanner to get the angle or reach you require. Or sometimes bike chain can be used to grab something you can't otherwise get to. Example:



From https://www.youtube.com/watch?v=E8qN9oK8Hzc From https://www.youtube.com/watch?v=E8qN9oK8Hzc






share|improve this answer





























    2














    It's good that there is at least some access to the square nut. There is a tool called a cotter pin puller. If you can get the point to jam alongside the nut, it should hold while you rotate the bolt head. Cotter pin pullers are variously sized and shaped. Bent a coathanger to simulate the size needed, then get the tool.






    share|improve this answer





























      2














      I faced a similar proposition last year. I bought an older house that had an ourdoor natural gas grill at some point and the top had literally rusted off so all I had left was this rusty column that ended in all sorts of jagged edges. It was bolted to a holder probably set in concrete that was built of something sturdier than the grill was. WD40 availed me not.



      What I did was I used my reciprocating saw with a metal blade to cut the bolts off. Noisy and painstaking, but it got the job done. Since your bolt is already loose, you should have daylight to get the blade between the nut and the plate (i.e. you don't need to damage the generator) and cut the nut off.



      Once the bolt is cut off, I would buy another from the local hardware store (get a nylon locking nut so it's easier next time) and you can ensure it will come off if you do this again.






      share|improve this answer





















      • Unfortunately, the generator casing would prevent me from getting a saw blade into it, but thanks anyway :)
        – ArtOfCode
        17 hours ago











      Your Answer








      StackExchange.ready(function() {
      var channelOptions = {
      tags: "".split(" "),
      id: "73"
      };
      initTagRenderer("".split(" "), "".split(" "), channelOptions);

      StackExchange.using("externalEditor", function() {
      // Have to fire editor after snippets, if snippets enabled
      if (StackExchange.settings.snippets.snippetsEnabled) {
      StackExchange.using("snippets", function() {
      createEditor();
      });
      }
      else {
      createEditor();
      }
      });

      function createEditor() {
      StackExchange.prepareEditor({
      heartbeatType: 'answer',
      autoActivateHeartbeat: false,
      convertImagesToLinks: false,
      noModals: true,
      showLowRepImageUploadWarning: true,
      reputationToPostImages: null,
      bindNavPrevention: true,
      postfix: "",
      imageUploader: {
      brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
      contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
      allowUrls: true
      },
      noCode: true, onDemand: true,
      discardSelector: ".discard-answer"
      ,immediatelyShowMarkdownHelp:true
      });


      }
      });






      ArtOfCode is a new contributor. Be nice, and check out our Code of Conduct.










      draft saved

      draft discarded


















      StackExchange.ready(
      function () {
      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f154112%2fhow-can-i-loosen-a-hard-to-reach-square-nut-whose-holder-is-broken%23new-answer', 'question_page');
      }
      );

      Post as a guest















      Required, but never shown

























      3 Answers
      3






      active

      oldest

      votes








      3 Answers
      3






      active

      oldest

      votes









      active

      oldest

      votes






      active

      oldest

      votes









      3














      Sounds like a nice project for a couple hours that grows into a multi-weekend odyssey!



      OPTION 1 I'd wedge a couple of thin paint scrapers under the exposed bolt head outside the shell of the unit, and take the bolt's head off with an angle grinder and a thin cut-off wheel



      BUT CONSIDER spark danger - given this is a generator there was probably petrol or diesel in the area. You'll want to vent it absolutely to remove all trace of gas fumes. And do this outside, with an extinguisher and sand handy.



      Once the bolt head is off, the bolt should drop into the housing and you can fish it out when the covers are removed.



      Assembly, well that's not the reverse. You'll want to find some way to bolt it together without risking the same again. A dirty hack is to put a new longer bolt in from the inside-to-outside. The nut will be on the outside and a bit of thread should be exposed. You can file two spanner-flats into the thread before or after assembly. Or you could hacksaw a flat slot across the end for a screwdriver.



      Also consider what other bolts on the unit might do the same in the future, and either reinforce their mounts with epoxy or fibreglass, or preemptively do a similar bolt hack.





      Option 2 - Cut the casing around the bolt head, and deal with it once the cover is off. You'll probably want to do a patch job on the case after-ward to control fumes etc.





      Option 3 - Make a tool to suit. This is probably the most laborious solution, but you know exactly where the nut is and how long your tool would have to be.



      From http://www.performanceforums.com/forums/showthread.php?67243773-dodgy-homemade-distributor-spanner From http://www.performanceforums.com/forums/showthread.php?67243773-dodgy-homemade-distributor-spanner



      Given how cheap tools are these days, there's no shame in sacrificing a cheap combo ring/open spanner to get the angle or reach you require. Or sometimes bike chain can be used to grab something you can't otherwise get to. Example:



      From https://www.youtube.com/watch?v=E8qN9oK8Hzc From https://www.youtube.com/watch?v=E8qN9oK8Hzc






      share|improve this answer


























        3














        Sounds like a nice project for a couple hours that grows into a multi-weekend odyssey!



        OPTION 1 I'd wedge a couple of thin paint scrapers under the exposed bolt head outside the shell of the unit, and take the bolt's head off with an angle grinder and a thin cut-off wheel



        BUT CONSIDER spark danger - given this is a generator there was probably petrol or diesel in the area. You'll want to vent it absolutely to remove all trace of gas fumes. And do this outside, with an extinguisher and sand handy.



        Once the bolt head is off, the bolt should drop into the housing and you can fish it out when the covers are removed.



        Assembly, well that's not the reverse. You'll want to find some way to bolt it together without risking the same again. A dirty hack is to put a new longer bolt in from the inside-to-outside. The nut will be on the outside and a bit of thread should be exposed. You can file two spanner-flats into the thread before or after assembly. Or you could hacksaw a flat slot across the end for a screwdriver.



        Also consider what other bolts on the unit might do the same in the future, and either reinforce their mounts with epoxy or fibreglass, or preemptively do a similar bolt hack.





        Option 2 - Cut the casing around the bolt head, and deal with it once the cover is off. You'll probably want to do a patch job on the case after-ward to control fumes etc.





        Option 3 - Make a tool to suit. This is probably the most laborious solution, but you know exactly where the nut is and how long your tool would have to be.



        From http://www.performanceforums.com/forums/showthread.php?67243773-dodgy-homemade-distributor-spanner From http://www.performanceforums.com/forums/showthread.php?67243773-dodgy-homemade-distributor-spanner



        Given how cheap tools are these days, there's no shame in sacrificing a cheap combo ring/open spanner to get the angle or reach you require. Or sometimes bike chain can be used to grab something you can't otherwise get to. Example:



        From https://www.youtube.com/watch?v=E8qN9oK8Hzc From https://www.youtube.com/watch?v=E8qN9oK8Hzc






        share|improve this answer
























          3












          3








          3






          Sounds like a nice project for a couple hours that grows into a multi-weekend odyssey!



          OPTION 1 I'd wedge a couple of thin paint scrapers under the exposed bolt head outside the shell of the unit, and take the bolt's head off with an angle grinder and a thin cut-off wheel



          BUT CONSIDER spark danger - given this is a generator there was probably petrol or diesel in the area. You'll want to vent it absolutely to remove all trace of gas fumes. And do this outside, with an extinguisher and sand handy.



          Once the bolt head is off, the bolt should drop into the housing and you can fish it out when the covers are removed.



          Assembly, well that's not the reverse. You'll want to find some way to bolt it together without risking the same again. A dirty hack is to put a new longer bolt in from the inside-to-outside. The nut will be on the outside and a bit of thread should be exposed. You can file two spanner-flats into the thread before or after assembly. Or you could hacksaw a flat slot across the end for a screwdriver.



          Also consider what other bolts on the unit might do the same in the future, and either reinforce their mounts with epoxy or fibreglass, or preemptively do a similar bolt hack.





          Option 2 - Cut the casing around the bolt head, and deal with it once the cover is off. You'll probably want to do a patch job on the case after-ward to control fumes etc.





          Option 3 - Make a tool to suit. This is probably the most laborious solution, but you know exactly where the nut is and how long your tool would have to be.



          From http://www.performanceforums.com/forums/showthread.php?67243773-dodgy-homemade-distributor-spanner From http://www.performanceforums.com/forums/showthread.php?67243773-dodgy-homemade-distributor-spanner



          Given how cheap tools are these days, there's no shame in sacrificing a cheap combo ring/open spanner to get the angle or reach you require. Or sometimes bike chain can be used to grab something you can't otherwise get to. Example:



          From https://www.youtube.com/watch?v=E8qN9oK8Hzc From https://www.youtube.com/watch?v=E8qN9oK8Hzc






          share|improve this answer












          Sounds like a nice project for a couple hours that grows into a multi-weekend odyssey!



          OPTION 1 I'd wedge a couple of thin paint scrapers under the exposed bolt head outside the shell of the unit, and take the bolt's head off with an angle grinder and a thin cut-off wheel



          BUT CONSIDER spark danger - given this is a generator there was probably petrol or diesel in the area. You'll want to vent it absolutely to remove all trace of gas fumes. And do this outside, with an extinguisher and sand handy.



          Once the bolt head is off, the bolt should drop into the housing and you can fish it out when the covers are removed.



          Assembly, well that's not the reverse. You'll want to find some way to bolt it together without risking the same again. A dirty hack is to put a new longer bolt in from the inside-to-outside. The nut will be on the outside and a bit of thread should be exposed. You can file two spanner-flats into the thread before or after assembly. Or you could hacksaw a flat slot across the end for a screwdriver.



          Also consider what other bolts on the unit might do the same in the future, and either reinforce their mounts with epoxy or fibreglass, or preemptively do a similar bolt hack.





          Option 2 - Cut the casing around the bolt head, and deal with it once the cover is off. You'll probably want to do a patch job on the case after-ward to control fumes etc.





          Option 3 - Make a tool to suit. This is probably the most laborious solution, but you know exactly where the nut is and how long your tool would have to be.



          From http://www.performanceforums.com/forums/showthread.php?67243773-dodgy-homemade-distributor-spanner From http://www.performanceforums.com/forums/showthread.php?67243773-dodgy-homemade-distributor-spanner



          Given how cheap tools are these days, there's no shame in sacrificing a cheap combo ring/open spanner to get the angle or reach you require. Or sometimes bike chain can be used to grab something you can't otherwise get to. Example:



          From https://www.youtube.com/watch?v=E8qN9oK8Hzc From https://www.youtube.com/watch?v=E8qN9oK8Hzc







          share|improve this answer












          share|improve this answer



          share|improve this answer










          answered yesterday









          Criggie

          807416




          807416

























              2














              It's good that there is at least some access to the square nut. There is a tool called a cotter pin puller. If you can get the point to jam alongside the nut, it should hold while you rotate the bolt head. Cotter pin pullers are variously sized and shaped. Bent a coathanger to simulate the size needed, then get the tool.






              share|improve this answer


























                2














                It's good that there is at least some access to the square nut. There is a tool called a cotter pin puller. If you can get the point to jam alongside the nut, it should hold while you rotate the bolt head. Cotter pin pullers are variously sized and shaped. Bent a coathanger to simulate the size needed, then get the tool.






                share|improve this answer
























                  2












                  2








                  2






                  It's good that there is at least some access to the square nut. There is a tool called a cotter pin puller. If you can get the point to jam alongside the nut, it should hold while you rotate the bolt head. Cotter pin pullers are variously sized and shaped. Bent a coathanger to simulate the size needed, then get the tool.






                  share|improve this answer












                  It's good that there is at least some access to the square nut. There is a tool called a cotter pin puller. If you can get the point to jam alongside the nut, it should hold while you rotate the bolt head. Cotter pin pullers are variously sized and shaped. Bent a coathanger to simulate the size needed, then get the tool.







                  share|improve this answer












                  share|improve this answer



                  share|improve this answer










                  answered yesterday









                  John Canon

                  4345




                  4345























                      2














                      I faced a similar proposition last year. I bought an older house that had an ourdoor natural gas grill at some point and the top had literally rusted off so all I had left was this rusty column that ended in all sorts of jagged edges. It was bolted to a holder probably set in concrete that was built of something sturdier than the grill was. WD40 availed me not.



                      What I did was I used my reciprocating saw with a metal blade to cut the bolts off. Noisy and painstaking, but it got the job done. Since your bolt is already loose, you should have daylight to get the blade between the nut and the plate (i.e. you don't need to damage the generator) and cut the nut off.



                      Once the bolt is cut off, I would buy another from the local hardware store (get a nylon locking nut so it's easier next time) and you can ensure it will come off if you do this again.






                      share|improve this answer





















                      • Unfortunately, the generator casing would prevent me from getting a saw blade into it, but thanks anyway :)
                        – ArtOfCode
                        17 hours ago
















                      2














                      I faced a similar proposition last year. I bought an older house that had an ourdoor natural gas grill at some point and the top had literally rusted off so all I had left was this rusty column that ended in all sorts of jagged edges. It was bolted to a holder probably set in concrete that was built of something sturdier than the grill was. WD40 availed me not.



                      What I did was I used my reciprocating saw with a metal blade to cut the bolts off. Noisy and painstaking, but it got the job done. Since your bolt is already loose, you should have daylight to get the blade between the nut and the plate (i.e. you don't need to damage the generator) and cut the nut off.



                      Once the bolt is cut off, I would buy another from the local hardware store (get a nylon locking nut so it's easier next time) and you can ensure it will come off if you do this again.






                      share|improve this answer





















                      • Unfortunately, the generator casing would prevent me from getting a saw blade into it, but thanks anyway :)
                        – ArtOfCode
                        17 hours ago














                      2












                      2








                      2






                      I faced a similar proposition last year. I bought an older house that had an ourdoor natural gas grill at some point and the top had literally rusted off so all I had left was this rusty column that ended in all sorts of jagged edges. It was bolted to a holder probably set in concrete that was built of something sturdier than the grill was. WD40 availed me not.



                      What I did was I used my reciprocating saw with a metal blade to cut the bolts off. Noisy and painstaking, but it got the job done. Since your bolt is already loose, you should have daylight to get the blade between the nut and the plate (i.e. you don't need to damage the generator) and cut the nut off.



                      Once the bolt is cut off, I would buy another from the local hardware store (get a nylon locking nut so it's easier next time) and you can ensure it will come off if you do this again.






                      share|improve this answer












                      I faced a similar proposition last year. I bought an older house that had an ourdoor natural gas grill at some point and the top had literally rusted off so all I had left was this rusty column that ended in all sorts of jagged edges. It was bolted to a holder probably set in concrete that was built of something sturdier than the grill was. WD40 availed me not.



                      What I did was I used my reciprocating saw with a metal blade to cut the bolts off. Noisy and painstaking, but it got the job done. Since your bolt is already loose, you should have daylight to get the blade between the nut and the plate (i.e. you don't need to damage the generator) and cut the nut off.



                      Once the bolt is cut off, I would buy another from the local hardware store (get a nylon locking nut so it's easier next time) and you can ensure it will come off if you do this again.







                      share|improve this answer












                      share|improve this answer



                      share|improve this answer










                      answered yesterday









                      Machavity

                      6,55511634




                      6,55511634












                      • Unfortunately, the generator casing would prevent me from getting a saw blade into it, but thanks anyway :)
                        – ArtOfCode
                        17 hours ago


















                      • Unfortunately, the generator casing would prevent me from getting a saw blade into it, but thanks anyway :)
                        – ArtOfCode
                        17 hours ago
















                      Unfortunately, the generator casing would prevent me from getting a saw blade into it, but thanks anyway :)
                      – ArtOfCode
                      17 hours ago




                      Unfortunately, the generator casing would prevent me from getting a saw blade into it, but thanks anyway :)
                      – ArtOfCode
                      17 hours ago










                      ArtOfCode is a new contributor. Be nice, and check out our Code of Conduct.










                      draft saved

                      draft discarded


















                      ArtOfCode is a new contributor. Be nice, and check out our Code of Conduct.













                      ArtOfCode is a new contributor. Be nice, and check out our Code of Conduct.












                      ArtOfCode is a new contributor. Be nice, and check out our Code of Conduct.
















                      Thanks for contributing an answer to Home Improvement Stack Exchange!


                      • Please be sure to answer the question. Provide details and share your research!

                      But avoid



                      • Asking for help, clarification, or responding to other answers.

                      • Making statements based on opinion; back them up with references or personal experience.


                      To learn more, see our tips on writing great answers.





                      Some of your past answers have not been well-received, and you're in danger of being blocked from answering.


                      Please pay close attention to the following guidance:


                      • Please be sure to answer the question. Provide details and share your research!

                      But avoid



                      • Asking for help, clarification, or responding to other answers.

                      • Making statements based on opinion; back them up with references or personal experience.


                      To learn more, see our tips on writing great answers.




                      draft saved


                      draft discarded














                      StackExchange.ready(
                      function () {
                      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f154112%2fhow-can-i-loosen-a-hard-to-reach-square-nut-whose-holder-is-broken%23new-answer', 'question_page');
                      }
                      );

                      Post as a guest















                      Required, but never shown





















































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown

































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown







                      Popular posts from this blog

                      1300-talet

                      1300-talet

                      Display a custom attribute below product name in the front-end Magento 1.9.3.8